If you’ve ever worked in a warehouse, manufacturing line, or packaging facility, you know how frustrating a misadjusted packing machine can be. One minute, your boxes are being sealed just right, and the next, they’re either crumpled so tight the tape’s tearing or so loose the contents might shift during shipping. As a packing machine supplier, I get asked all the time: “How do I fix the height of my machine without breaking it?” Today, I’m breaking this down step by step—no fancy jargon, no confusing steps, just what works for the machines we sell. Packing Machine

First, let’s get one thing straight: adjusting your packing machine’s height isn’t a one-and-done task. It depends on the type of machine you’re using, too. We supply three main types, and each has its own little quirks for height. There’s the semi-automatic case sealer (the one most small to mid-sized warehouses use), the automatic vertical form fill seal machine (for bags or pouches), and the palletizing packing machine (for stacking boxes on pallets). I’ll cover the basics that apply to all, then dive into the type-specific stuff so you don’t waste time guessing.
Before you touch any knobs or levers, do a quick pre-check. A lot of people skip this, and that’s where mistakes happen. First, unplug the machine (or flip the safety switch, if it’s a big automatic model) to avoid any accidental starts. I’ve seen a guy last year reach under his semi-auto sealer and bump the lever—machine kicked on, almost took his finger off. Not worth it. Next, grab a tape measure and a sample of the boxes or packages you’re using right now. Don’t just guess; measure the height of a fully folded, sealed (or ready to seal) box. That’s your target number. If you’re packing pouches, measure the max height of the filled pouch. For pallets, it’s the height you need the machine to stack boxes to—like standard 48-inch pallets, so your machine should stop at 48 inches. Also, check for any dirt or debris stuck under the machine’s feet or around the adjustment bolts. A dirty bolt won’t turn smoothly, and you’ll end up with an uneven height that ruins your boxes.
Step 1: Basic Height Adjustment for Semi-Automatic Case Sealers
These are the workhorses—you load a box, push it through, and it seals top and bottom tape. Their height adjustment is usually on both sides, not just one. First, find the adjustment cranks under each side of the machine (they’re big, plastic or metal knobs, usually labeled “HEIGHT ADJ”). Turn the left crank clockwise to raise the machine, counterclockwise to lower it. Do the same for the right one—here’s the trick: you have to turn both the same number of times. If you turn the left one two full turns clockwise, turn the right one two full turns too. If you don’t, the machine will tilt slightly, and the tape will apply unevenly (half the tape on the box, half on the conveyor). Once you’ve turned both, test the height with your sample box. If it’s still too high, do another half turn on both sides, test again. Stop when the box moves through the machine without hitting the top or bottom tape heads—no pinching, no sliding too loosely.
Another quick fix here: if your machine has fixed feet, some models let you add or remove shims (thin metal or plastic pieces) under the feet to level it. Shims are great if your warehouse floor is a little uneven (let’s be real, most floors are). Just make sure you don’t overdo it—one shim per foot is enough, more than that and the machine will wobble, which will mess up the box alignment.
Step 2: Adjusting Vertical Form Fill Seal (VFFS) Machines
These ones make and seal bags from a roll of film, so their height is tied to how high the product fill is. First, locate the main height control panel—most have a digital display now, no more guessing with cranks. On the panel, you’ll see a button labeled “HEAD HEIGHT” or “FORMING TUBE HEIGHT.” The forming tube is the part that folds the film into a bag shape, so its height needs to match the fill height of your product. If you’re packing 10-inch tall snack bags, the forming tube should be set to 10 inches. If you’re switching to 6-inch bags, lower the tube by hitting the “-” button on the panel.
Wait, test a sample bag after every adjustment—these machines can be finicky. If you set it too low, the bag will crumple at the top when you seal it; too high, you’ll waste film because the machine will cut a longer bag than needed. Also, check the guide rolls for the film—if those are at the wrong height, the film will pull unevenly, which makes the bag height off. Just loosen the guide roll bolts, adjust the roll so it’s level with the forming tube, then tighten. Easy fix, and it fixes 90% of film-related height issues.
Step 3: Palletizing Packing Machines (Robotic or Conveyor)
Palletizing machines stack boxes, so their height is about the conveyor belt height and the stacking height limit. First, the conveyor belt that brings boxes to the palletizer needs to match the height of the pallet jack or forklift you’re using. If your forklift forks are 12 inches off the ground, set the conveyor to 12 inches—too high, and the forklift can’t slide the pallet under; too low, and boxes might bump the ground. The adjustment here is usually a set of bolts on the conveyor legs—loosen them, lift or lower the belt to your target height, then tighten the bolts. Make sure to test with a empty pallet first, before loading boxes.
The stacking height is another thing: most palletizers have a limit switch that stops the machine when it reaches a certain height. If you’re shipping standard pallets (48 inches), set the switch to 48 inches. To adjust it, find the switch along the vertical rail of the machine, loosen the clamp that holds it in place, slide it up or down, then clamp it tight. Test stacking 5 boxes, measure the total height, and tweak if needed. If the switch is too low, you’ll end up with a half-stacked pallet that won’t fit on the truck; too high, you risk the stack tipping over.
Common Mistakes I See (And How to Fix ’Em)
After years as a packing machine supplier, I’ve seen almost every mistake when it comes to height adjustments. Let’s go over the big ones so you don’t make ’em:
-
Adjusting only one side: Like I said earlier, semi-automatic sealers need both sides turned the same. Last year, a guy turned the left side three turns and the right one two—his boxes were tilting so bad, the tape kept peeling off the corner. Simple fix: mark the number of turns on one side before you do the other, so you match it.
-
Forgetting to lock the adjustment: So many people crank the machine to the right height, then forget to tighten the bolts or re-lock the cranks. When the machine runs, it vibrates, and the height will slip. Always double-check—after you adjust, turn the cranks clockwise (if they’re a locking crank) until they’re tight, or tighten the bolts on the legs.
-
Not checking floor level: If your warehouse floor is sloped, even if your machine is level, boxes might slide to one side. I recommend getting a small $10 level (the bubble kind, not the digital fancy one) and placing it on the conveyor or the machine’s top bar. If it’s not level, add shims under the lowest foot until the bubble is dead center. That fixes so many alignment issues.
-
Adjusting during a run: Don’t stop mid-production to tweak the height—you’ll waste time, and if the machine’s running hot, the parts might shift. Stop at the end of a batch, let the machine cool down a minute, then adjust. It’ll save you more time in the long run.
When to Call a Pro (And When Not To)
Most height adjustments are DIY, but there are a couple times when you should reach out to someone—if you’re dealing with a brand-new machine, or if you’ve adjusted three times and it’s still not working. We get calls all the time from guys who’ve tried to adjust their VFFS machine’s forming tube and broke a sensor, or stripped a crank bolt. That’s why we offer free 15-minute tech calls for all our customers—just shoot us a message, and we’ll walk you through it. For older machines, if the adjustment mechanism is rusted or broken, we can also sell replacement parts, no hassle.
If you’ve tried all these steps and your machine still isn’t packing right, don’t stress. As a packing machine supplier, our whole job is to make sure your line runs smooth, and height adjustments are just a small part of that. The last thing we want is for you to waste product or time because of a tiny height issue. We get it—packing is fast-paced, and you can’t afford to have downtime.

At the end of the day, adjusting your packing machine’s height doesn’t have to be complicated. Just take it step by step, do the pre-check, match both sides for sealers, test sample after sample, and lock everything down. If you run into a snag, we’re here to help. If you’re in the market for a new packing machine too, or you need replacement parts for the one you have, hit us up. We don’t do fancy sales pitches—just straight talk about what works for your business. No hidden fees, no long contracts, just machines that get the job done right.
Packing Machine Reference: Industrial Packaging Machinery Maintenance Guide, National Association of Packaging and Processing Machinery Suppliers (2022)
Zhengzhou Tongding Machinery Equipment Co., Ltd.
Zhengzhou Tongding Machinery Equipment Co., Ltd. is one of the most professional packing machine manufacturers and suppliers in China, featured by quality products and good price. Please rest assured to buy CE approved packing machine made in China here and get quotation from our factory. Also, customized service and 5 years warranty are available.
Address: Kexue Avenue Industrial Park, Xingyang City, Zhengzhou City, Henan Province
E-mail: admin@tongdingmachine.com
WebSite: https://www.td-machinerygroup.com/